...
| Web interface of the STARFACE | Menu "Configuration" | Menu "Routing" |
|---|---|---|
|
|
|
...
Routing controls which of the existing lines is used for an outgoing call and in which order the existing lines are used. All of the settings made in this section relate to the routing of outgoing calls on STARFACE and have no influence on incoming calls. Routing is used to control which of the existing lines are used for an outgoing call, or the order in which the existing lines are used.
| Hinweis |
|---|
Note: Completion of the numbers during calls to the local area network are also influenced by routing. |
In this tab, the Routing priority The drop-down menu can be menu Routing Priority is used to define configure which routing is used for the outgoing calls.
In detail, these are:
Static: The STARFACE automatically selects one of the existing lines and attempts tries to set up establish the call once using over this line. If a line is selected on which the call number to be signaled is not configured is selected, the call number display is suppressed. This option is represents the STARFACE basic setting of STARFACE and only works reliably in very simple scenarios, e.g. with just only one line. It is always recommended to select another routing priority such as Line or COR rule.
| Hinweis |
|---|
| Note: If the “CLIP no Screening” feature is activated on STARFACE for the automatically selected line, the call number display is not suppressed. |
Line: In the case of this routing priority, the The line used for the outgoing call is determined by the call number to be signaled (see also Configuring Phone Numbers for a User). The call is set up using established via the line on which the call number is configured. Only one attempt is made and should this not be successfulif this attempt is unsuccessful, the outgoing call is abortedcancelled.
COR Rule: If this option is selected, the The rules defined in the "Cost Optimized Routing – Location Based Routing" tab shall apply. If a line is selected for the outgoing call on which the call number to be signaled is not configured is selected for the outgoing call, , the provider suppresses the call number display is suppressed by the provider or even rejects the outgoing call is even rejected.
During local area dialing, e.g. to the number 1234, the dialing user’s primary call number is used to complete the country and area codes. If a primary external call number is not configured for a user, the STARFACE general management section is used to complete the country and area codes.
| Hinweis |
|---|
| Note: If the “CLIP no Screening” feature is activated on STARFACE on the line specified by the rules, the call number display is not suppressed. |
LBR Rule: If this option is selected, the The rules defined in the "the Cost Optimized Routing – Location Based Routing" tab shall apply. If a line is selected for the outgoing call on which the call number to be signaled is not configured is selected for the outgoing call, , the provider suppresses the call number display is suppressed by the provider or even rejects the outgoing call is even rejected.
During local area dialing, e.g. to the number 1234, the STARFACE general management section is used to complete the country and area codes.
| Hinweis |
|---|
Note: If the “CLIP no Screening” feature is activated on STARFACE on the line specified by the rules, the call number display is not suppressed. |
Line + COR: In the case of this routing priority, an An attempt is first made to assign a line to the outgoing call using via the setting Line setting described above. If this assignment is not possible , or if the corresponding line is not available, the COR rules are applied.
...
| Hinweis |
|---|
Note: The use of the rule Line + COR is recommended if possible. |
Routing During Unavailability
The drop-down menu can be used to select how calls to users who do not have an available telephone and who have not created any call redirection definitions are handled.
The following options are available to choose from:
to To deposit: The caller is immediately forward forwarded to the drop point whose number was entered in the line configuration. The call is rejected if no drop point is configured.
Reject: The call is rejected and not forwarded.
...
Configuring a COR
...
Rule
A new COR rule can be created using the "New Rule" buttonbuttons or
.
Phone number: The fully qualified call number to which the created COR rule is to apply must be stored at this point. In this regard, it must be noted that STARFACE always dials outgoing numbers in the international format, ie.eg. with 0049 at the start of the call number for German numbers or 0041 for Swiss numbers in Switzerland.
The “best match” rule also applies when using the COR rules. This means that, if there are several COR rules which would apply to a selected number, the COR rule which has the most matching digits is used.
...
A COR rule is time-controlled using the day-based checkboxes and the freely selectable “From – To” time period. It is also possible to display several time periods within a COR rule; to do this, a new time period must be created using the "+New Time Frame" button . This new time period may must not overlap with one of the other periods within the COR rule.
Under Specify line sequence, the sequence of the lines used can be stored for each configured time period. The order of the configured lines determines their priority. This means that an attempt is made to establish a connection using the topmost line first of all, then using the second line, etc., until all of the assigned lines have been run through.
...
| Hinweis |
|---|
Note: If no lines are assigned to a COR rule, no outgoing calls can be made on the configured call numbers. |
Call-by-call numbers which are prefixed to the number actually called during a connection establishment process can be stored in the Pre-Preselection field. If, for example, the number 072112233 is selected and the added pre-prefix “888” is added, this results in 888004972112233.
...